Injection moulding · Sharjah
Alaska Machinery — injection moulding machines in Sharjah
They sell machines. The old site only said they fix them.
What it is
A replacement for a WordPress site that was still shipping the theme’s demo content — Tony Stark, the Golden Gate Bridge, a London vacancy and "since 1983". Their real record is 100+ machines installed and 60+ control retrofits, and the old home page animated those from zero and usually never fired, so visitors read "0+".
The numbers
- Machines installed
- 100+
- Control retrofits to 2800T
- 60+
- Robots commissioned
- 50+
- Sections, after the cut
- 26 → 14
What is inside
- Public site and an engineers’ toolbox, deliberately split
- Clamp-force and cell sizing solved from the part, not looked up
- Four automations behind the site
In more detail
What else the old site was still publishing
Subscription plans the company does not sell. "Serving since 1983" — seven years before the founder was born. Those sat on the same page as Tony Stark, the Golden Gate Bridge and the London vacancy. All of it was the WordPress theme's demo content, live on the client's own domain. The first job on any replacement is reading what the current site actually publishes.
How the toolbox sizes a machine from the part
Projected area of the part and its runners, multiplied by the cavity pressure of the material, gives the clamp force, and fifteen per cent is added for safety. Shot weight comes from wall thickness, cavity count and the density of the polymer. The result is matched against the hydraulic range they represent, from 400 to 13,000 kN.
Why the track record is printed as plain text
The numbers panel above carries three of the record figures. There is a fourth: fifty-plus servo conversions, on presses up to 3300 tonnes. All four are printed as static text on the new site, because the old page counted them up from zero on scroll and the count usually never started. An animation that can fail is worse than none on the number that is the whole pitch.
Why the buyer's page and the engineer's page were split
A buyer looking for a supplier and an engineer sizing a cell want different pages, so they were split rather than merged into one long homepage. The public side carries the company and the machine range; the toolbox carries clamp sizing and cost per part — including what one second off the cycle time does to a year of production.
Built with
It boots in your browser and runs the real logic — no form, no sales call.
Common questions
What size injection moulding machine does my part need?
It comes from the part, not from a chart. Put the part into the toolbox on the site — length, width, wall, cavities, material, runner share — and it solves the force, adds the safety margin and checks the shot against barrel capacity, then names a machine from the range.
Why does the machine size still matter if the shot is small?
Because a shot under a fifth of barrel capacity leaves material sitting in a hot barrel long enough to degrade. The toolbox flags that case and tells you to go a size down — the opposite of what a machine supplier is usually assumed to want you to hear.
Does Alaska Machinery sell machines or only service them?
They sell them. The old site was the reason anyone thought otherwise — it read like a service shop with someone else's demo content on top. They have been trading since 2018, and the machines they sell are the same hydraulic range the toolbox sizes against, 400 to 13,000 kN.
Can you replace a WordPress site that has drifted like this?
Yes — this page is that job. It starts with reading what the live site is actually publishing, which is the only way a problem like Tony Stark gets found at all. Then a rebuild, with the real record printed where the demo content used to be. Scope decides the figure, and it is quoted per project in writing after a call.
Related reading
More of the work
- JD PROP AIReal-estate command centre
- JD Property OSManage and maintain, one account
- Atlas ERPAI-native ERP for GCC contractors
- StockBookBuilt around one man’s spreadsheet
- ComplyGCCAML / KYC for UAE fintechs
- MRP Businessman ServicesPublish what the industry hides
- Estate VaultFor land deals that arrive on WhatsApp
- CourseDeskTutor-side automation
- RippleWhat should we develop next?
- ScanversePhone to photoreal 3D
- Aluminium & Glass demoNothing typed in from a catalogue
- Tyre & Oil demoPrices benchmarked to the real market
- Cafe demoThe licence says cold and hot
- Barbershop demoBarbering, booked properly
- Excel PlasticsEvery bottle solved, not modelled
JD Software Solutions — a four-person software studio in the United Arab Emirates. We build the system, hand over the code, and stay on to run it.